Trying to copy PR1 level 0 to PR1 level 1

This topic has 7 replies, 2 voices, and was last updated 15 years, 10 months ago by Yamil Velez.

Creator

Topic
February 6, 2009 at 2:27 pm #50617
Yamil Velez
Participant
Hi All

I am trying to copy a segment in this case is PR1 level 0 to PR2 level 1.

example 0(0).PR1 -> 1(0).0(0).PR1

I tried the following but was unsucessful to get the message across.

iterate

type = segment

basis = 0(0).PR1

variable = %s1

pathcopy 0(0).PR1 -> 1(0).0(0).PR1

If anybody can help me with this problem, I would be very grateful.

Thanks

Yamil
Creator

Topic

Viewing 6 reply threads

Author

Replies
- February 6, 2009 at 3:59 pm #66801
  Jim Kosloskey
  Participant
  Yamil,
  
  First I think your basis is incorrect – double check that.
  
  Second even when the basis is correct, you need to place your iteration counter in the proper place in the address paths of your inbound and outbound fields in the PATHCOPY.
  
  email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.
- February 6, 2009 at 9:01 pm #66802
  Yamil Velez
  Participant
  Hi Jim
  
  I tried this but it still does not pass over.
  
  Thanks
  
  Yamil
- February 6, 2009 at 9:11 pm #66803
  Yamil Velez
  Participant
  Hi Jim
  
  Sorry forgot to added the changes. This is what I have now but it still does not pass the segment over.
  
  type = segment
  
  basis = 0(0).PR1
  
  variable = %s1
  
  pathcopy 0(0).PR1(%s1) -> 1(0).0(0).PR1 (%s1)
  
  Thanks
  
  Yamil
- February 6, 2009 at 10:26 pm #66804
  Jim Kosloskey
  Participant
  Yamil,
  
  Are you sure that is a repeating segment and not a repeating group?
  
  Run the inbound message through the HL/7 Testing tool and show us all of the PR1.
  
  email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.
- February 9, 2009 at 2:56 pm #66805
  Yamil Velez
  Participant
  Hi Jim
  
  I am not sure if I did this right but I went testing tool and here is the output
  
  0(0).PR1(0).#1(0).[0] : >””< 0(0).PR1(0).#2(0).[0] : >””< 0(0).PR1(0).#3(0).[0] : >””< 0(0).PR1(0).#4(0).[0] : >””< 0(0).PR1(0).#5(0).[0] : >””< 0(0).PR1(0).#6(0).[0] : >””< 0(0).PR1(0).#8(0).[0] : >””< 0(0).PR1(0).#9(0).[0] : >””< 0(0).PR1(0).#11(0).[0] : >””< 0(0).PR1(0).#12(0).[0] : >””< 0(0).PR1(0).UNKNOWN.[0] : >””
- February 9, 2009 at 5:24 pm #66806
  Jim Kosloskey
  Participant
  Yamil,
  
  What you sent looks like this is a repeating segment (it would be nice to have a message with multiple PR1s to make sure).
  
  Make sure your outbound variant indeed has the PR1 as a repeating segment and not a repeating group.
  
  If both are truly rpeating segments, then what you have shown should work.
  
  Please note I don’t work a lot with PATHCOPY so I am not sure of that syntax.
  
  Also I note your tester output shows all of the PR1 field inbound are ‘active nulls’.
  
  What Message/event Type are these messages?
  
  email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.
- February 11, 2009 at 8:15 pm #66807
  Yamil Velez
  Participant
  Hi Jim
  
  Thanks for the help it looks like you said the error may be in the message, for some reason when I tried a different message the PR1 segment went though
  
  Thanks again
  
  Yamil
Author

Replies

Viewing 6 reply threads

The forum ‘Cloverleaf’ is closed to new topics and replies.