Clovertech

Usman Azher

Forum Replies Created

Viewing 14 replies – 1 through 14 (of 14 total)
  • Author
    Replies
  • January 6, 2017 at 8:24 pm in reply to: Get site and host name in tcl #84793
    Usman Azher
    Participant

      Thank you. I was able to get the site and thread name. Is there a way to get the host name as well? The reason I ask is that we have two cloverleaf servers.

      August 18, 2015 at 3:07 pm in reply to: Replacing with E #82988
      Usman Azher
      Participant

        Charlie,

        That worked perfectly fine. Thank you very much for your help.

        Usman Azher

        May 18, 2015 at 6:32 pm in reply to: Using string length in a if statement within a translation #82549
        Usman Azher
        Participant

          I am sorry I do not have much experience with Tcl. Can you explain to me where in the translation I am supposed to insert the format command? Also, is this tcl proc going to be inside the translation or as a pre or post proc?

          May 14, 2015 at 3:41 pm in reply to: Help with translation #82545
          Usman Azher
          Participant

            I was not aware of doing basis this way. Can any one shed light on this?

            May 14, 2015 at 3:31 pm in reply to: Help with translation #82544
            Usman Azher
            Participant

              Keith I used your recommendation and it works. Thank you very much

              May 14, 2015 at 3:26 pm in reply to: Help with translation #82543
              Usman Azher
              Participant

                group 1

                May 14, 2015 at 3:23 pm in reply to: Help with translation #82542
                Usman Azher
                Participant

                  Here are the iterate action properties for all of the iterates

                  May 14, 2015 at 1:58 pm in reply to: Help with translation #82539
                  Usman Azher
                  Participant

                    I have tried it in the testing tool and also from an engine run. I have also tried having the same variants on both side but for some reason the iteration is not working for me. The basis I have used are as follows:

                    1

                    1(0).0(0).NTE

                    1(0).1

                    1(0).1(0).NTE

                    March 10, 2015 at 1:41 pm in reply to: Cloverleaf resending multiple messages #82196
                    Usman Azher
                    Participant

                      Yes it does. We looked at all of the settings and they seem fine. Sort of stumped here

                      March 9, 2015 at 9:43 pm in reply to: Cloverleaf resending multiple messages #82194
                      Usman Azher
                      Participant

                        Yes all of the acks came back within milli seconds and all of the messages were sent out at the same time.

                        March 9, 2015 at 9:22 pm in reply to: Cloverleaf resending multiple messages #82190
                        Usman Azher
                        Participant

                          Our timeout is set to 120s. The acks were positive and the receiving system got the message 5 times.

                          March 9, 2015 at 7:49 pm in reply to: Failed message count & TPS Inbound reply #82118
                          Usman Azher
                          Participant

                            Looks like that worked. The proc just needed some clean up work!

                            Thanks alot!

                            February 26, 2015 at 7:23 pm in reply to: Failed message count & TPS Inbound reply #82117
                            Usman Azher
                            Participant

                              Hey Keith,

                              We ran the commands you mentioned and figured out our proc was not configured to handle replies of types CR and CE. It was only handling replies of type AA, AE, AR and CA. The acks we were getting were of CR type since we were resending messages and the receiving system recognized them as duplicates. Then we figured that we were using a variable in comments that was not initialized anywhere. Will give you guys the update once we see more messages crossing through.

                              Thanks!

                              December 17, 2014 at 3:04 pm in reply to: SMAT Database Search #81745
                              Usman Azher
                              Participant

                                Elisha,

                                Thank you for your response. After using the parenthesis in the search criteria we were able to solve our problem. We can now search for multiple messages using just one search criteria. Re-sending messages is much quicker now!

                                Thank you!

                              • Author
                                Replies
                              Viewing 14 replies – 1 through 14 (of 14 total)