Our helpdesk has stated that it goes into an Opening Status.

Here is text from the DI Manager log.
Time Stamp                        State     Message
6/7/2015 05:37:42.057    ERROR  Remote-host closed server process : Port 49103 at IP Address shspwim
6/7/2015 05:37:47.632    STATE    TcpClientConnect^imdevio
6/7/2015 05:38:03.367    TCPIP…Read more

On that feed we had the kill replies proc configured on the inbound replies section of OUTBOUND Tab.

We did not have the OUTBOUND only option selected. We did try selecting that option and will see…Read more

we will set that up and see if these errors go away.

thanks to everyone who offered a suggestion on this topic. 😀

I think your right about only the one file being able to be used at anytime.

Let you know if I hear anything different.

It was just a way to move them over from test and have them edited for different recipients and text in the email part of the alerts.

Thanks for your reply.

I think I will probably end up doing this modification, but I think they are asking do much of their work. We are trying to avoid getting in a position where we have to do their maintenance.

Thank you for your time and help with this.

Knowing that there is a cost is helpful.

I saw your comment and I am interested in finding out if CSC has any costs associated with using it, if we already have Cloverleaf?

I will test it and see how it works. So is this only grabbing the first field after the ~?

Any examples for a TCL proc that will do that type of task?

Unknown host: 10.80.46.11; nested exception is:

I had it working until I found that it would fail if the field was blank or if it had more than on provider. Now I have to do some modifications to my proc.

I am searching for the Certified OS/Chipset. Is that posted on Clovertech?

One other question, is there an advantage to having an Active/Active node configuration as compared to the an Active/passive node configuration?

I got it working as far as dropping the file where I need it, but I keep overwriting the orginal file with the next message.

I am going to work on the proc to see if I give the file name a more unique name if that will allow the second ORM to write to a new file and so on and so on.

If I still have issues, I will…Read more

Once I had a better understanding of the format of the Messages the Vendor sends, we were able to modify the variant and with just a few modifications get the xlate working.

The counters are working correctly and we are getting the NTE following the ORC moved down below the first OBR segment that follows the ORC and it is following the…Read more

The topic was just brought up that it could happen (more than one host server running) if we do not start the host server from the…Read more

It was mentioned that Linux and Cloverleaf do not manage the host server well and more than one session or instance of the host server can be running on the server at the same time. If the OS is Linux.

Our support analyst has stated that this is incorrect, we only need to be logged on as HCI and we can restart the host…Read more

I’ll attach a screen shot of my xlate to this comment and hope to hear back soon.

I was able to modify my variant so that it I did not have repeating OBX segments within multiple groups.

Then it was just a matter of getting the Iteration variables within the correct basis place holders. Also I want to thank you for setting me straight about adding a Group or other variable within the basis declaration of a nested…Read more

The variants associated with this interface are used only by this interface. they are only ORU_R30s that we have on our system.

The OBX segments in the variants were part of two groups. Once I removed them from the ORC to CTL group and configured them only to be grouped with their own NTE segments, then it was just a bit of modification for…Read more

These segments are all part of a group. I can try your suggestion, but I am fuzzy on how to create the counter.

I have tried some of the ways from other posts and not having any luck.

Such as

copy =$%s99 -> @$%s99

System did not like this declaration.

It is keeping the port open in Bridges.

Thanks for the idea.

B&Blood -> Blood
SPUTUM&Sputum -> Sputum

We have it configured to use the original value.

I setup a pre proc to escape all Ampersands in OBR15, but not getting anywhere.

Here is the code to pre proc

######################################################################
proc escAmpersandOBR15 { args } {
 …Read more

it ended up being a problem with my client.

I just received a new pc and we had the PC Tech department install Cloverleaf. There was a step that was missed after installing the client from the CD. We need to install updates. Normally we just copy the updates from a client that already has them installed.

I went out and grabbed those files…Read more

Now that I have new messages coming from the POCT, I have a few issues.

First I was getting the IR mismatch error. I clear them by creating variables rather than doing some of the =literal value -> to field.

Now I am only getting the MSH segment of the…Read more

I was able to get to work, but I was curious about if tha 0 means the first element in as string. i.e. 12324 does the 0 represt the 1 or all five digits?

So if I want to skip the 1 of the string I could start with at setting a 1 instead of 0.

good idea.

0(0).OBX(%s1).#5 to  0(0).OBX(0).#5(%s1)

Then the ERROR goes away in the process error log. But we only process the first OBX line and then it stops.

[xpm :xlt :WARN/0:softmed_xlate:12/30/2011 14:29:43] IF data fetch produced multiple values.
[xlt…Read more

We are still having problems with this if statement. I notice that if I move the iteration variable listed in the long if statement, then the PARSE ERROR goes away, but we stop processing the message after the first OBX segment.

Here is a screen dump of the translation portions of this iteration an if statement that is causing the errors.

I’ll check that out.

Can you clearify what specifically are MSI details? I went to that site, and looked around, but read nothing about its use with Cloverleaf.

Did I miss something or is the level of knowledge over my head?

I was checking out your proc. Do you know or have any ideas of how to pull the transaction ID of a message from the database, by using a proc?

we want to be able to pull data from the database, not the HL7 message.

What shows the inbound adt count?

{MID {{DOMAIN 0} {HUB 0} {NUM 29872483}}}

How about just regular FTP? We have been attempting to configure interfaces using the ftp protocol and we get this error.

[fset:wrte:ERR /0:          ftp:07/08/2011 09:39:03] Error while trying to write test.txt. Detailed error:Uploading to a URL without a file name! Curl errCode:3 Curl error: URL using bad/illegal format or missing…

We go through Mckesson.

Thanks for the information.