Xlate question

[Sebastien Bazile]

I  need to make some changes to an MDM_T04. There are some fields in TXA segment that need to be either altered or hardcoded with but when I do a BULKCOPY and then COPY the remaining segments. I’m only getting the MSH segment and EVEN with just field 1 and nothing else.

Original message above. Thanks for all the help.

MSH|^~&|DXOne|Dental|Medical|Medical|20170613170337||MDM^T04|3|T|2.3||||AL

EVN|T04|20170613170337||01

PID|1||I000000560||Test^Dent^^^||19500613000000|M|||Test^^NEW  YORK^NY^10039^||^^^tdent@imc.com^^|||Single||V00000008141|||||||||||

PV1|1||DENT||||DEF_PROV^DEF_PROV^DEF_PROV^|||||||||||

TXA|1|CN|TX|20170613000000|DEF_PROV^DEF_PROV^DEF_PROV^|20170613170321||20170613170337|MILLDAV^^^|||DDB_NOTE1069279X2|||||LA||AV|||MILLDAV^^^^^^^^^^^^^^20170613170337

OBX|1|TX|||Test Note 3||||||F

OBX|2|TX|||Line 2||||||F

OBX|3|TX|||Line 3||||||F

OBX|4|TX|||||||||F

OBX|5|TX|||

---

Signed on Tuesday, June 13, 2017 at 5:03:35 PM  

---

||||||F

OBX|6|TX|||

---

Provider: ENTERPRISE –  ,  — Clinic: CENTRAL

---

||||||F

0(0).MSH(0)  : >|^~&|DXOne|Dental|Medical|Medical|20170613170337||MDM^T04|3|T|2.3||||AL< 0(0).EVN(0)  :  >|T04< 0(0).PID(0)  :  >< 0(0).PV1(0)  :  >< 0(0).TXA(0)  :  >< 0(0).OBX(0)  :  ><

Topic

[Jim Kosloskey]

Do your inbound and outbound variants match?

email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.

[Sebastien Bazile]

yes, I just don’t know what’s going on. I used PATHCOPY too, same thing.

[Jim Kosloskey]

Does just the BULKCOPY work?

If not then normally that is a mismatch in the ib and ob message structures

email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.

[Jim Kosloskey]

Have you run the inbound message through the HL/7 tester using the variant you are using in your Xlate?

email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.

[Sebastien Bazile]

That I haven’t done. I will try it tonight and see what I get. Thanks a lot.

[Sebastien Bazile]

I’m still just getting the MSH segment when I ran it through the HL7 tester.

[Jim Kosloskey]

So your variant does not match the data.

What release of Cloverleaf?

Did you see any errors when running the HL/7 Tester?

Take a screen shot of your Message structure from the HL/7 configurator (not in the Xlate) and email that to me or attach to a post here.

email: jim.kosloskey@jim-kosloskey.com 29+ years Cloverleaf, 59 years IT - old fart.

[Robert Kersemakers]

If you only see the MSH segment in the HLt-tester, then I think your segments don’t end with the required CarriageReturn.

Do a hcihexdump of this test-message and check which character(s) end each segment. It should be x0D.

Zuyderland Medisch Centrum; Heerlen/Sittard; The Netherlands

[Sebastien Bazile]

Thank you so much. Didn’t think about that.

[Sebastien Bazile]

Thank you everyone for all your help. There was an issue with the file. I did hcihexdump like you said and found out the segments were ending with 0xa instead of oxd. fixed it and now testing working out great. Thanks again gentlemen.

[Author]

Replies