Clovertech

windows cl 6.1 having problem sending data using smat

› Clovertech Forums › Read Only Archives › Cloverleaf › Cloverleaf › windows cl 6.1 having problem sending data using smat

  • Creator
    Topic
  • August 13, 2013 at 4:21 pm #53778
    Donna Bailey
    Participant

      Has anyone experienced this before?

      I’m on a windows 2008 server…loaded cl6.1 and trying to test smat data…. I load the smat file, I can select one message and have it resend through the inbound thread without a problem, but when I select all the messages to resend, it starts (percentage bar says 11%), but then hangs.  I can cancel out, but then I have to “End Task” of the screen.  The smat file has 35000+ records.  Not sure if that could be part of the problem?

      Thanks for your help!

      Donna Bailey
      Tele: 315-729-3805
      dbailey@microstar.health
      Micro Star Inc.

    • Creator
      Topic
    Viewing 7 reply threads
    • Author
      Replies
      • August 13, 2013 at 5:28 pm #78917
        Jon Melin
        Participant

          I have experienced this before with large result messages. The only solution that seemed to work for me was to archive a majority of the messages in the SMAT. If you have the ability to do that, I would start there.

          Thank you

        • August 13, 2013 at 6:05 pm #78918
          Donna Bailey
          Participant

            I tried to break up the smat into about 10,000 records and it did the same thing..is that what you mean?

            Donna Bailey
            Tele: 315-729-3805
            dbailey@microstar.health
            Micro Star Inc.

          • August 13, 2013 at 6:15 pm #78919
            Jon Melin
            Participant

              What I did was “cycle save” and archive the messages out. Essentially only leaving a week or so worth of messages in the SMAT (depending on your message load). Crontab can be used to schedule archives like this.

              Hope this helps.

              Thank you

            • August 13, 2013 at 6:42 pm #78920
              Donna Bailey
              Participant

                I’m actually taking a production file (it’s only half the day)…to a new cloverleaf install to test/validate data….I normally take a whole day’s worth of data and run it through my new cloverleaf threads and compare the output smat….this is NOT going to be an easy feat, I have feeling….

                I’m at the point now of breaking down into about 5000 messages to separate files and then I can use them to send through the NetMonitor…I may have to open up ticket with Infor…

                Thanks,

                Donna Bailey
                Tele: 315-729-3805
                dbailey@microstar.health
                Micro Star Inc.

              • August 13, 2013 at 6:46 pm #78921
                Donna Bailey
                Participant

                  I’m actually taking a production file (it’s only half the day)…to a new cloverleaf install to test/validate data….I normally take a whole day’s worth of data and run it through my new cloverleaf threads and compare the output smat….this is NOT going to be an easy feat, I have feeling….

                  I’m at the point now of breaking down into about 5000 messages to separate files and then I can use them to send through the NetMonitor…I may have to open up ticket with Infor…

                  Thanks,

                  Donna Bailey
                  Tele: 315-729-3805
                  dbailey@microstar.health
                  Micro Star Inc.

                • August 13, 2013 at 6:51 pm #78922
                  Jon Melin
                  Participant

                    Ok. I thought you were talking test. Does it matter which chuck of messages you try to view (beginning / end) ? I have seen certain messages cause issues like this before as well.

                    Thank you,

                    Jon

                  • August 13, 2013 at 7:58 pm #78923
                    Donna Bailey
                    Participant

                      I figured it out….I am pulling 5.5 data and trying to send it through on 6.1….I had to run hcismatconvert.

                      Thanks for you input…I sure appreciate it!

                      Donna Bailey
                      Tele: 315-729-3805
                      dbailey@microstar.health
                      Micro Star Inc.

                    • August 13, 2013 at 8:52 pm #78924
                      Jon Melin
                      Participant

                        Awesome! Not sure how much help I was but glad you figured it out! 🙂

                    • Author
                      Replies
                    Viewing 7 reply threads
                    • The forum ‘Cloverleaf’ is closed to new topics and replies.