PDL

[manoj thotakur]

Hi,

Is there any PDL in cloverleaf that can be used to look for hex 02 ?

I have X12 interface on TCP/IP interface where sender is encapsulating  the message with hex 02 and hex 03 .

my regular TCP/IP pdl in cloverleaf only reads hex 0b to begin a message and hex 1c0d to end a message .

Does any body have the custom PDL for the hex 02 ?

Thanks Very Much.

Topic

[Charlie Bursell]

Protocol -> TCPIP -> Encapsulated -> Configure -> User -> Start Block – End Block

[manoj thotakur]

Hi Charles , I have used the user and used the 2 and 3 as START  and END block.

some how the  mesg was  not continuous its been chopped off when it try to read the message

]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] 12:40:14 ibEpic_HDX/logMsg

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] #-| Begin |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–]              *ZZ*1

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14] #-| End |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] 12:40:14 ibEpic_HDX/logMsg

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] #-| Begin |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14] #-| End |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] 12:40:14 ibEpic_HDX/logMsg

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] #-| Begin |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] *1

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14] #-| End |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] 12:40:14 ibEpic_HDX/logMsg

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] #-| Begin |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[tcl :out :INFO/0:   ibEpic_HDX:–/–/—- –:–:–] 0171006*12

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14] #-| End |

---

 

[tcl :out :INFO/0:   ibEpic_HDX:10/06/2017 12:40:14]

[Charlie Bursell]

I would have to see an example message.  Does it have embedded control characters?

When I get a chance I will set up a test case and try it but without knowing the format of your message it may not mean much

BTW, it is Charlie, not Charles   😆

[Charlie Bursell]

I just tested this and it worked for me.  I set Start Block as X02 and End Block as X03.

I set up a receiving thread with the protocol.  I set another thread to send using same protocol and port number.  A resend of an XML message from the sending thread resulted in reception of full XML message (rather large) in the receiving thread.

[Author]

Replies