Clovertech

TCL in Crontab Problem

› Clovertech Forums › Read Only Archives › Cloverleaf › Cloverleaf › TCL in Crontab Problem

  • Creator
    Topic
  • October 28, 2005 at 3:51 pm #48114
    Nicole Goodyear
    Participant

      I have a tcl proc that deletes any saved process logs older than 2 months.  I have setup a cronjob that executes this tcl proc but I am getting the following error when it runs:

      /hci/qdx5.1/integrator/ms4test/tclprocs/processLogs.tcl[12]: proc:  not found.

      /hci/qdx5.1/integrator/ms4test/tclprocs/processLogs.tcl[18]: 0403-057 Syntax error at line 20 : `}’ is not expected.

      The crontab looks like this:

      34 11 * * * /usr/bin/ksh -c ‘eval `/hci/qdx5.1/integrator/sbin/hcisetenv -root ksh /hci/qdx5.1/integrator ms4test`;/hci/qdx5.1/integrator/ms4test/tclprocs/proce

      ssLogs.tcl’>/hci/joe/processtestlogs.log 2>&1

      Any thoughts or suggestions on this would be greatly appreciated!

      Thanks

    • Creator
      Topic
    Viewing 8 reply threads
    • Author
      Replies
      • October 28, 2005 at 6:58 pm #57682
        Rentian Huang
        Participant

          your crob job looks no problem. have you tested ur processLogs.tcl? use the TPS testing tool, and see whether u still get the same Syntax error. also make sure the proc is in the correct directory.

          sam   8)

        • October 31, 2005 at 1:46 pm #57683
          Nicole Goodyear
          Participant

            Thanks for the reply.  The proc does work in the testing tool and it is current directory.  

            Any other ideas?!

          • October 31, 2005 at 2:44 pm #57684
            Ricci Graham
            Participant

              Nicole,

              You might try hardcoding the directory structure in the proc so it will find the proc.

              Also, can you post what is on line 20 that it is kicking an error out on?

              Ricci

            • October 31, 2005 at 3:33 pm #57685
              Nicole Goodyear
              Participant

                Here is my tcl proc.

                proc processLogs {} {

                   set getMonth [fmtclock [getclock] “%m”]

                   set deleteMonth 0

                   set formatMonth 0

                   if {$getMonth != 10 || $getMonth != 11 || $getMonth != 12} {

                set formatMonth [string trimleft $getMonth 0]

                   } else {

                set formatMonth $getMonth

                   }

                   if {[cequal $formatMonth “1”]} {

                set deleteMonth 11

                   } elseif {[cequal $formatMonth “2”]} {

                set deleteMonth 12

                   } else {

                set deleteMonth [expr $formatMonth – 2]

                   }

                #   remove all files that do equal deleteMonth

                   rm /hci/process_logs_test/*.$deleteMonth*

                }

                One thing I am confused with, how can hardcoding the directory structure inside the proc find the proc if it cannot access it in the first place?  Could you please clarify? Thanks!

              • October 31, 2005 at 3:50 pm #57686
                Ricci Graham
                Participant

                  Nicole,

                  On the second error, it looks like it thinks you have an extra brace, but when I copy and paste your proc in my editor and check it, all the braces line up, so that is a little strange. Did you remove a brace before posting?

                  To answer your questions on clarification, I misunderstood. You’re right, if it can’t find the proc in the first place, it won’t be able to read anything from it.

                  Another thought, have you run this proc from the command line and see if it runs? Before I add anything to Cron, I run it from the command line first to see if I get any errors.

                  Ricci

                • October 31, 2005 at 4:21 pm #57687
                  Nicole Goodyear
                  Participant

                    Hi Ricci,

                    I did not remove any curly braces before I posted.  I just tried running this from the command line as root and hci and I am receiving the exact same errors.  

                    Thanks,

                    Nicole

                  • October 31, 2005 at 4:58 pm #57688
                    Bill Bertera
                    Participant

                      I think you need to make the file a script and not a procedure. remove the “proc processlogs {”  line, and the final }. Add the tcl intepreter to the first line:

                      #!/hci/qdx5.2/integrator/bin/hcitcl

                      (or wherever your tcl is).

                      make it executable: chmod +x filename.tcl (if you’re on unix).

                      and then try to run it.

                    • October 31, 2005 at 6:20 pm #57689
                      Anonymous
                      Participant

                        If your on a unix system I would recommend making your scripts cloverleaf release independent with the below as the 1st three lines of your script.

                        #!/usr/bin/sh

                        # reload using exec but make it a comment for tcl

                        exec hcitcl “$0” “$@”

                        The first line may vary depending on your unix version

                        #!/usr/bin/sh  is for aix

                        the sh exec will use the environment variables to find hcitcl

                        and root must be set

                      • October 31, 2005 at 7:16 pm #57690
                        Nicole Goodyear
                        Participant

                          Hi Bill,

                          That’s it!  Thank you so much for your help 🙂

                          Nicole

                      • Author
                        Replies
                      Viewing 8 reply threads
                      • The forum ‘Cloverleaf’ is closed to new topics and replies.